Welcome Guest!

You have no items in your shopping cart.

You have no items in your shopping cart.

Loading..

Product was successfully added to your shopping cart.

5

Product was successfully added to your comparison list.

Application Process


1 - Application process for Car Side Styling Graphics:-

Quick and Easy Application Procedure for Autographix Car Decals

  1. 1. Clean the application surface.
    2. Position the decal using masking tape.
    3. Remove the decal and gently peel off the backing liner.
    4. Spray soap water on the adhesive side (Backside) of the decal.
    5. Apply the decal on the car.
    6. Run the squeegee on the decal to remove excess water.
    7. Gently peel off the top application film from the decal holding it at a 180° angle.

Kindly Note

In case of any bubbles due to trapped air or water in the decal, gently pierce the bubble using a pin or needle and
run the squeegee over it.
If the decal extends along the door edges it can easily be cut using a paper knife.
The car can be washed as usual from the next day.


2 - Application process for Roof Wrap : -

2 - Application process for Roof Wrap : -

Quick and Easy Application Procedure for Autographix Roof Wrap

  1. You will require

    Roof wrap decal

    Soapy Water

    Squeegee

    Paper Knife

    Masking Tape

     

    Two people are required for smooth application of the roof wrap

    Application Process -

    1. Remove the top rubber strips. Ensure that the car roof is clean and dry, especially along the edges and groves (if any).

    2. Align the roof wrap as required and fasten using the masking tape.

    3. You can provision for any extensions on the roof such as roof antennas, etc by creating a hole in the wrap using a paper knife.

    4. Lift the wrap from the front edge of the roof for approximately 1-1.5 feet and fasten it using the masking tape.

    5. Peel off the backing liner from the lifted section of the wrap and cut the liner using a paper knife.

    6. Firmly hold the adhesive side of the wrap in an outstretched manner and gently run the squeegee in wide even strokes starting from the center towards the front edge of the      roof.

    7a. Starting from the front of the roof peel off the backing liner from underneath the roof wrap in horizontal bands of approximately 1-1.5 feet at a time exposing the adhesive            side of the wrap.

    b. Start applying the adhesive exposed section of the wrap on the car, by gently running the squeegee in wide vertical strokes starting from the center of the roof.

    8. In case of grooves on the car roof, ensure that the roof wrap is tightly applied along the contours of each groove with the help of the squeegee or your fingers.

    9. In case of any air bubbles or wrinkles, the film can be gently peeled off (be careful not to overstretch it) and reapplied.

    10. Cut the excess wrap along all the edges of the roof using a paper knife and leave approximately 15mm of wrap.

    11. Tuck the edges of the wrap inside the roof with the help of the squeegee.

     

    Kindly Note

    -       Be sure to remove the rubber pads (if present) on the roof before application.

    -       The car can be washed as usual from the next day.


3 - Application process for Bonnet Wrap : -

2 - Application process for Bonnet Wrap : -

Quick and Easy Application Procedure for Autographix Bonnet Wrap

  1. You will require

    Roof wrap decal

    Soapy Water

    Squeegee

    Paper Knife

    Masking Tape

     

    Two people are required for smooth application of the bonnet wrap

    Application Process -

    1. Ensure that the surface of the car bonnet is clean and dry especially along the edges and grooves.

    2. Align the roof wrap as required and fasten using the masking tape.

    3. Starting from the top left corner of the wrap, peel off the backing liner till the masking tape at the centre of the wrap. 

    4. Cut off the peeled away backing liner using a paper knife, leaving a margin of 2 inches from the fastening line. Neatly fold and tuck the backing liner of the margin beneath          the remaining section of the wrap.

    5. Firmly hold the adhesive side of the wrap in an outstretched manner and gently run the squeegee in wide even strokes starting from the centre towards the side of the                bonnet.

    6. Repeat the same process for the other side of the bonnet.

    7. In case of any air bubbles or wrinkles, the wrap can be gently peeled off (be careful not to overstretch it) and reapplied.

    8. Leave approximately 7 inches along all the edges of the Bonnet and cut the excess wrap using a paper knife.

    9. Open the bonnet and cut small vertical sections of the excess wrap using the paper knife.

    10. Tuck the edges of the wrap inside the bonnet with the help of the squeegee and cut the remaining wrap using the paper knife.

     

    Kindly Note

    -       The car can be washed as usual from the next day.


4 - Application process for Scratch Protection Kits : -

Quick and Easy Application Procedure for Autographix Scratch Protection Kits

  1. You will require

    Scratch Guard

    Masking Tape

    Dry Cloth

     

    The complete kit comprises of

    - Two Front Bumper Guards - To be applied on the front bumper corners between the headlight and fog light
    - Two Rear Bumper Guards - To be applied on the rear bumper corners between the safety light and tail light
    - Two Side Mirror Guards - To be applied along the curvature of the car side mirrors
    - Four Door Edge Guards - To be applied along the car door edges

    Application Process -

    1. Ensure the application surface is clean and dry.
    2. Position the scratch guard on the application area and remove the backing liner.
    3. With the help of your fingers firmly press the scratch guard in wide even strokes to ensure there are no air bubbles.
    4. In case of any bubbles, the strip can be gently peeled off and reapplied.

     

    Kindly Note

    - Be careful not to touch the adhesive while application.

  2. - The car can be washed as usual from the next day.